Journals →  Chernye Metally →  2022 →  #7

Chernye Metally


 

The journal "Chernye Metally" No. 7-2022 was published, which is mainly dedicated to the 20th anniversary of the Vyksa branch of NUST "MISiS". As part of the anniversary selection, 4 articles were published, prepared jointly by specialists from the branch and the Vyksa Metallurgical Plant. These articles describe production technologies, processing modes, mechanical properties and microstructure of cast thin slabs, welded and seamless pipes.

 

The issue is headed with a publication by JSC Tulachermet specialists on hot repairs of blast furnace linings; one more information material about the technical achievements of this plant will be published in the September issue of the journal "Chernye Metally".

 

As usual, the journal presents articles on metal forming. In this issue, authors from the Ural Federal and Magnitogorsk State Technical Universities, as well as JSC RusNITI, inform about new technologies for channel rolling, wire drawing, and pipe pressing, respectively.

 

The same issue contains publications in the sections "Foundry", "Heating and heat treatment", "Metal science and metallography" and "Energy", prepared by specialists from the Chuvash State, Siberian State Industrial, Tomsk Polytechnic, Moscow State Construction, Magnitogorsk State Technical Universities and Naberezhnye Chelny Institute (branch) of Kazan Federal University.

 

The journal also publishes a report on the international forum "Dialogue of Metallurgists: Industry Development Forecast until 2030", which was held in Moscow in April 2022.

 

Please find more details below, or order your printed or electronic version of the Journal.


Production of cast iron
ArticleName Hot repair of blast furnace lining – a way to reduce its carbon footprint
ArticleAuthors D. V. Fedorenko, A. A. Vorotyntsev, E. M. Shcheglov, A. N. Sankin
ArticleAuthorsData

JSC Tulachermet, Tula, Russia:

D. V. Fedorenko, Chief Engineer, e-mail: fedorenko_dv@metholding.com
A. A. Vorotyntsev, Deputy Chief Engineer for Production
E. M. Shcheglov, Head of Production and Technical Department
D. P. Kholodny, Head of Blast Furnace Shop

Foundry production
ArticleName Aluminodipine conborate phosphate molding and core mixtures for steel and iron castings
ArticleAuthors I. E. Illarionov, A. V. Korolev, I. A. Strelnikov, L. A. Ivanova
ArticleAuthorsData

I. N. Ulianov Chuvash State University, Cheboksary, Russia:

I. E. Illarionov, Dr. Eng., Prof., Dept. of Materials Science and Metallurgical Processes, e-mail: tmilp@rambler.ru
A. V. Korolev, Cand. Eng., Associate Prof., Dept. of Materials Science and Metallurgical Processes
I. A. Strelnikov, Cand. Eng., Associate Prof., Head of the Dept. of Materials Science and Metallurgical Processes
L. A. Ivanova, Senior Lecturer, Dept. of Materials Science and Metallurgical Processes

Rolling and other processes of OMD
ArticleName Optimization of roll calibrations for channel rolling. Message 3. The space of channel calibration schemes
ArticleAuthors D. L. Schwartz, A. M. Mikhailenko, E. I. Salikhianova
ArticleAuthorsData

Ural Federal University, Ekaterinburg, Russia:

D. L. Schwarts, Dr. Eng., Associate Prof., Head of the Dept. of Metal Forming
A. M. Mikhailenko, Cand. Eng., Associate Prof.
E. I. Salikhyanova, Assistant, Postgraduate student, e-mail: ustinova1694@gmail.com

ArticleName Influence of dynamic inhomogeneity of the stress-strain state on the modes of wire drawing in a monolithic conical die
ArticleAuthors S. M. Goloviznin, V. A. Kharitonov
ArticleAuthorsData

Nosov Magnitogorsk State Technical University, Magnitogorsk, Russia:
S. M. Goloviznin, Cand. End., Associate Prof., Head of the Dept. of Metallurgy and Standardization, e-mail: smgoloviznin@magtu.ru
V. A. Kharitonov, Cand. Eng., Prof., Dept. of Materials Processing Technologies

20 years of the Vyksa branch of NUST MISIS
ArticleName Features of formation of the structure of thin slabs cast at different speeds, their influence on the structure and properties of hot-rolled steel
ArticleAuthors E. L. Vorozheva, D. V. Kudashov, A. A. Khlybov, K. S. Smetanin
ArticleAuthorsData

Vyksa Steel Works, Vyksa, Russia:

E. L. Vorozheva, Сhief Specialist, e-mail: vorozheva_el@vsw.ru

K. S. Smetanin, Chief Specialist, e-mail: smetanin_ks@vsw.ru

 

Vyksa branch of the National University of Science and Technology “MISIS”, Vyksa, Russia:

D. V. Kudashov, Cand. Eng., Director, e-mail: kudashov_dv@vsw.ru

 

Nizhny Novgorod State Technical University named after R. E. Alekseev, Nizhny Novgorod, Russia:

A. A. Khlybov, Dr. Eng., Prof., Dept. of Materials Science, Technology of Materials and Heat Treatment of Metals, e-mail: hlybov_52@mail.ru

ArticleName Influence of cooling conditions on the microstructure and impact strength of welded joints made by automatic submerged multi-arc welding
ArticleAuthors S. V. Zharkov, P. P. Stepanov, O. A. Bagmet, L. I. Efron
ArticleAuthorsData

Vyksa Steel Works, Vyksa, Russia:

S. V. Zharkov, Chief Specialist, Center for Research Laboratories, Engineering and Technology Center
P. P. Stepanov, Cand. Eng., Director of the Engineering and Technology Center
O. A. Bagmet, Cand. Eng., Head of the Laboratory of the Center for Research Laboratories of the Engineering and Technology Center

 

Vyksa Steel Works, Vyksa, Russia1 ; Vyksa branch of the National University of Science and Technology “MISIS”, Vyksa, Russia2
L. I. Efron, Dr. Eng., Prof.2, Scientific Supervisor of the Engineering Research Center1, e-mail: Lefron@omk.ru

ArticleName Study of the expansion process taking into account the contact interaction of the deforming tool and pipe
ArticleAuthors M. A. Tovmasyan, S. V. Samusev, N. V. Kholodova, I. V. Myalkin
ArticleAuthorsData

Vyksa branch of the National University of Science and Technology “MISIS”, Vyksa, Russia:

M. A. Tovmasyan, Senior Lecturer, Dept. of Technologies and Equipment for Metal Forming, e-mail: i-margarit@yandex.ru
N. V. Kholodova, Senior Lecturer, Dept. of Technologies and Equipment for Metal Forming
I. V. Myalkin, Cand. Eng., Associate Prof., Dept. of Electrometallurgy


National University of Science and Technology “MISIS”, Moscow, Russia:

S. V. Samusev, Dr. Eng., Prof., Dept. of Metal Forming

ArticleName Simulation of the operation of two-roll screw piercing of steels of the 13Cr type
ArticleAuthors A. V. Korol, A. S. Aleshchenko, A. R. Shamilov, A. V. Goncharuk
ArticleAuthorsData

Vyksa Steel Works, Vyksa, Russia1 ; Vyksa branch of the National University of Science and Technology “MISIS”, Vyksa, Russia2:

A. V. Korol, Cand. Eng., Associate Prof., Сhief Specialist in Seamless Pipe Production Technology1, Dept. of Technologies and Equipment for Metal Forming2, e-mail: korol_av@omk.ru

 

Vyksa Steel Works, Vyksa, Russia1 ; National University of Science and Technology “MISIS”, Moscow, Russia2:
A. R. Shamilov, Chief Specialist in Rolling Tools1, Postgraduate Student, Dept. of Metal Forming2, e-mail: shamilov_ar@omk.ru


Vyksa branch of the National University of Science and Technology “MISIS”, Vyksa, Russia:

A. V. Goncharuk, Cand. Eng., Prof., Dept. of Technologies and Equipment for Metal Forming, e-mail: gon@misis.ru

 

National University of Science and Technology “MISIS”, Moscow, Russia:

A. S. Aleshchenko, Cand. Eng., Associate Prof., Head of the Dept. of Metal Forming, e-mail: aleschenko.as@misis.ru

Production of pipes
ArticleName Increasing the crack resistance when pressing pipes made of 08Kh13N4M1F steel
ArticleAuthors A. V. Vydrin, A. S. Zhukov, D. Yu. Zvonarev, M. A. Pavlova
ArticleAuthorsData

South Ural State University, Chelyabinsk, Russia1 ; Russian Research Institute of the Tube and Pipe Industry (RusNITI), Chelyabinsk, Russia2:

A. V. Vydrin, Dr. Eng., Prof., Dept. of Machinery and Technologies for Materials Forming1, Chief Researcher2


Russian Research Institute of the Tube and Pipe Industry (RusNITI), Chelyabinsk, Russia:

D. Yu. Zvonarev, Cand. Eng., Head of the Laboratory for Modeling Technological Processes
M. A. Pavlova, Senior Engineer, Laboratory for Modeling Technological Processes, e-mail: pavlova@rosniti.ru

 

Volzhsky Pipe Plant, Volzhsky, Russia:

A. S. Zhukov, Quality Director

Heating and heat treatment
ArticleName Situational optimization of the work of the thermal department, taking into account the ordering instability
ArticleAuthors S. M. Kulakov, A. I. Musatova, N. V. Martyushev, A. I. Karlina
ArticleAuthorsData

Siberian State Industrial University, Novokuznetsk, Russia:

S. M. Kulakov, Cand. Eng., Prof., Dept. of Automation and Information Systems, Head of the REC "Center for Information Technologies and Control Automation Systems"
A. I. Musatova, Senior Lecturer, Dept. of Management and Sectoral Economics

 

National Research Tomsk Polytechnic University, Tomsk, Russia:
N. V. Martyushev, Cand. Eng., Associate Prof., Dept. of Materials Science, Engineering School of New Production Technologies

 

Moscow State University of Civil Engineering, Moscow, Russia:
A. I. Karlina, Cand. Eng., Researcher, e-mail: karlinat@mail.ru

Metallology and metallography
ArticleName Investigation of the formation of service properties of parts made from forgings of microalloyed steels after controlled cooling from stamping temperatures
ArticleAuthors V. G. Shibakov, D. L. Pankratov, A. M. Valiev, R. V. Shibakov
ArticleAuthorsData

Naberezhnye Chelny Institute (branch) of Kazan Federal University, Naberezhnye Chelny, Russia:

V. G. Shibakov, Dr. Eng., Prof., Head of the Dept. of Mechanical Engineering, e-mail: vladshib50@gmail.com
D. L. Pankratov, Dr. Eng., Director of the Higher Engineering School, e-mail: pankratovdl@gmail.com
A. M. Valiev, Cand. Eng., Associate Prof., Dept. of Mechanical Engineering, e-mail: cct-ineka@yandex.ru
R. V. Shibakov, Cand. Eng., Associate Prof., Dept. of Mechanical Engineering

Power engineering
ArticleName Diagnostics of the charge melting stage by arc current and voltage higher harmonics for EAF and LF of various classes
ArticleAuthors A. A. Nikolaev, G. P. Kornilov, P. G. Tulupov, S. S. Ryzhevol
ArticleAuthorsData

Nosov Magnitogorsk State Technical University, Magnitogorsk, Russia:

A. A. Nikolaev, Cand. Eng., Head of the Dept. of Automated Electric Drive and Mechatronics, e-mail: aa.nikolaev@magtu.ru
G. P. Kornilov, Dr. Eng., Head of the Dept. of Power Supply of Industrial Enterprises, e-mail: korn_mgn@mail.ru
P. G. Tulupov, Junior Researcher, Dept. of Power Supply of Industrial Enterprises, e-mail: tulupov.pg@mail.ru
S. S. Ryzhevol, Postgraduate Student, Dept. of Automated Electric Drive and Mechatronics, e-mail: snaffls18@gmail.com

Journals →  Chernye Metally →  2022 →  #7